The CLARKE-ALTO 27PROPANE BURN is a propane powered floor burnisher. This unit has a flexible pad driver that accommodates any surface and the most uneven floors get a smooth finish. The CLARKE-ALTO 27PROPANE BURN has an ergonomic adjustable handle giving the operator a better comfort level allowing for less fatigue and longer use of the unit.Pad speed: 1500 RPMs
Productivity (per hour): 33,000 sq.ft
Propane tank (required): 20 lb
Product length: 59 in (149.9 cm)
Product width: 29.3 in (74.4 cm)
Product height: 43 in (109.2 cm)
Product weight: 240 lb (108.8 kg)
27PROPANE BURN Parts and Support
The CLARKE-ALTO 27PROPANE BURN is a propane powered floor burnisher. This unit has a flexible pad driver that accommodates any surface and the most uneven floors get a smooth finish. The CLARKE-ALTO 27PROPANE BURN has an ergonomic adjustable handle giving the operator a better comfort level allowing for less fatigue and longer use of the unit.
Pad speed: 1500 RPMs
Productivity (per hour): 33,000 sq.ft
Propane tank (required): 20 lb
Product length: 59 in (149.9 cm)
Product width: 29.3 in (74.4 cm)
Product height: 43 in (109.2 cm)
Product weight: 240 lb (108.8 kg)
Pad speed: 1500 RPMs
Productivity (per hour): 33,000 sq.ft
Propane tank (required): 20 lb
Product length: 59 in (149.9 cm)
Product width: 29.3 in (74.4 cm)
Product height: 43 in (109.2 cm)
Product weight: 240 lb (108.8 kg)
Parts
Can't find what you need? Click here or call 1-800-USA-CLEAN
Diagrams
- View all diagrams
- - Commonly Asked For Parts
- - KAWASAKI FH500/FH541 - Muffler - Dust Bonnet - Emission System
- - Pad Holders
- -- Model Chart
- -Engine- Kawasaki FS481V
- 12 Volt Fuel System
- Bearing Assembly
- Belt Chart
- Engine - Kawasaki FH500v/FH541V
- Frame Assembly
- Fuel System Overview
- Handle Assembly
- NON-OEM Dust Bonnet and Cage Option
- Pad Driver Assembly
- Vacuum Fuel System
- Wiring Diagram - Honda 13hp
- Wiring Diagram - Kawasaki 14
- Wiring Diagram - Kawasaki 14 Envirogard
- Wiring Diagram - Kawasaki 17
- Wiring Diagram - Kawasaki 17 Envirogard
- Wiring Diagram - Onan P248
Manuals
Bulletins
- Safety Procedures
- Service Bulletin - New Air Filter
- TSS Bulletin #40 - Frosting of a Fuel Regulator on a Propane Buffer
- TSS Bulletin 38 - Propane Buffer Battery Guide
- TSS Bulletin 39 - Checking the battery and charging system on a propane buffer with Kawasaki
- TSS Bulletin 41 - Adjusting the Oil Pressure Switch on a Kawasaki FS481V
Repair Guides
- Check All Wiring
- Check Wiring Harness
- Replace Battery
- Replace Battery Cable
- Replace Defective Wiring
- Replace Solenoid
- Replace Starter
- Replace Stator
- Replace the Key Switch
- Replace the Voltage Regulator
- Replace Wiring Harness
- Test Voltage Regulator
- Test Battery Voltage & Do a Load Test
- Test Key Switch
- Test Solenoid
- CHECK AIR BREATHER FILTERS
- Check Compression
- Check Muffler
- Check Oxygen Sensor
- Fill Oil to Proper Level
- Pull Heads and Check Valve Seats
- Replace Air Breather Filters
- Replace Heads
- Replace Muffler
- Replace Oil Pressure Switch
- Replace Oxygen Sensor
- Set Valves and Recheck Compression
- Test Oil Pressure Switch
- Check Fuel Lines
- Open Tank Valve
- Replace Fuel Lines
- Replace Fuel Regulator
- Replace Tank
- Replace the Lock Off
- Test Regulator
- Test Tank Valve
- Test the Lock Off
- Tighten Fuel Connector
- Check Spark Plug Wires
- Check Spark Plugs
- Replace Ignition Module
- Replace Kill Switch Wire Harness
- Replace Spark Plugs
- Test Ignition Module
- Test Kill Switch Wire Harness