AQUA RIDE SE

AQUA RIDE SE

Nilfisk-Advance AQUA RIDE SE

Interested in purchasing equipment?

Contact our Experts!

Need help finding a part?

Ask our Team! The compact AquaRide extractor will sweep and extract up to 18,500 square feet of carpet in one pass in one hour which is an impressive 400% productivity gain over walk-behind extractors. The AquaRide extractor features dual-cleaning modes- a low-moisture mode for maintenance or interim cleaning and a restoration mode for deep-cleaning.

The AquaRide SE is now available with the on-board AXP detergent system. Based on Advance's Smart Solutions innovations, the AXP system accurately dispenses detergent at the manufacturers' recommended dilution ratios without waste. Unlike wall-mounted detergent dispensing units, the onboard AXP detergent system takes the guesswork out of correct detergent dispensing. A magnetic control on the AXP detergent cartridge allows for the required dilution ratio to be preset. The correct amount of detergent is then mixed with clean water at the time solution is applied to the floor, allowing for effective and efficient cleaning results.

The AXP system allows for the use of any brand of detergent, including those that are green-certified. Multiple AXP cartridges can be kept on the shelf filled and preset so there are no hassles when switching detergents during cleaning. Imagine the convenience and flexibility to switch detergents within seconds, and without having to clean out the solution tank.

The semi-transparent AXP cartridges are reusable and operator friendly, allowing you to easily spot when refills are needed. The appropriately labeled cartridges are easily transportable to switch detergent types while on the go.

Coverage Rate Low moisture mode – 18,500 ft2 /hour (1,720 m2 ) Restoration mode – 8,000 ft2 /hour (745 m2 ) Slow low moisture/Fast Restoration 10,000 ft2 /hour (930 m2 )
Solution Tank 45 gal (170 L) capacity, Rotationally molded polyethylene with drain hose.
Recovery Bladder 25 gal (95 L) capacity, PVC material, equipped with float ball screen and a 36 in (91 cm), long 1.5 in (3.8 cm) diameter drain hose
Brush Speed 900 rpm
Brush Length 28 in (71 cm)
Brush System 2 motors at 0.75 hp, 560 W each
Solution Pump Low moisture mode – 0.5 gpm (1.9 L/min) at 100 psi Restoration mode – 1.1 gpm (4.1 L/min) at 100 psi
Vacuum Motor 0.80 hp, 600 W motor with gear transmission, band brake and dynamic braking.
Drive System 1.1 hp, 840 W motor with gear transmission, band brake and dynamic braking. Programmable speeds up to 4.5 mph transport, and 3.8 mph scrubbing.
Power Source Six 6 V / 238 Ah (@ 20 hour rate) batteries or Six 6 V / 305 Ah (@ 20 hour rate) batteries
Sound Level 73 dB A @ operator position.
Min. Turn-around Aisle Width 63 in (160 cm) right or left
Dimensions Length – 60 in (152 cm) Width – 31 in (79 cm) Height – 51 in (130 cm)
Weight Net – 625 lb (283 kg) without batteries Net – 1,165 lb (528 kg) with batteries Shipping – 1,433 lb (649 kg) with batteries and charger

AQUA RIDE SE

Interested in purchasing equipment?

Contact our Experts

Need help finding a part?

Ask our Team!
The compact AquaRide extractor will sweep and extract up to 18,500 square feet of carpet in one pass in one hour which is an impressive 400% productivity gain over walk-behind extractors. The AquaRide extractor features dual-cleaning modes- a low-moisture mode for maintenance or interim cleaning and a restoration mode for deep-cleaning.

The AquaRide SE is now available with the on-board AXP detergent system. Based on Advance's Smart Solutions innovations, the AXP system accurately dispenses detergent at the manufacturers' recommended dilution ratios without waste. Unlike wall-mounted detergent dispensing units, the onboard AXP detergent system takes the guesswork out of correct detergent dispensing. A magnetic control on the AXP detergent cartridge allows for the required dilution ratio to be preset. The correct amount of detergent is then mixed with clean water at the time solution is applied to the floor, allowing for effective and efficient cleaning results.

The AXP system allows for the use of any brand of detergent, including those that are green-certified. Multiple AXP cartridges can be kept on the shelf filled and preset so there are no hassles when switching detergents during cleaning. Imagine the convenience and flexibility to switch detergents within seconds, and without having to clean out the solution tank.

The semi-transparent AXP cartridges are reusable and operator friendly, allowing you to easily spot when refills are needed. The appropriately labeled cartridges are easily transportable to switch detergent types while on the go.

Coverage Rate Low moisture mode – 18,500 ft2 /hour (1,720 m2 ) Restoration mode – 8,000 ft2 /hour (745 m2 ) Slow low moisture/Fast Restoration 10,000 ft2 /hour (930 m2 )
Solution Tank 45 gal (170 L) capacity, Rotationally molded polyethylene with drain hose.
Recovery Bladder 25 gal (95 L) capacity, PVC material, equipped with float ball screen and a 36 in (91 cm), long 1.5 in (3.8 cm) diameter drain hose
Brush Speed 900 rpm
Brush Length 28 in (71 cm)
Brush System 2 motors at 0.75 hp, 560 W each
Solution Pump Low moisture mode – 0.5 gpm (1.9 L/min) at 100 psi Restoration mode – 1.1 gpm (4.1 L/min) at 100 psi
Vacuum Motor 0.80 hp, 600 W motor with gear transmission, band brake and dynamic braking.
Drive System 1.1 hp, 840 W motor with gear transmission, band brake and dynamic braking. Programmable speeds up to 4.5 mph transport, and 3.8 mph scrubbing.
Power Source Six 6 V / 238 Ah (@ 20 hour rate) batteries or Six 6 V / 305 Ah (@ 20 hour rate) batteries
Sound Level 73 dB A @ operator position.
Min. Turn-around Aisle Width 63 in (160 cm) right or left
Dimensions Length – 60 in (152 cm) Width – 31 in (79 cm) Height – 51 in (130 cm)
Weight Net – 625 lb (283 kg) without batteries Net – 1,165 lb (528 kg) with batteries Shipping – 1,433 lb (649 kg) with batteries and charger

Nilfisk-Advance AQUA RIDE SE Parts and Support

The compact AquaRide extractor will sweep and extract up to 18,500 square feet of carpet in one pass in one hour which is an impressive 400% productivity gain over walk-behind extractors. The AquaRide extractor features dual-cleaning modes- a low-moisture mode for maintenance or interim cleaning and a restoration mode for deep-cleaning.

The AquaRide SE is now available with the on-board AXP detergent system. Based on Advance's Smart Solutions innovations, the AXP system accurately dispenses detergent at the manufacturers' recommended dilution ratios without waste. Unlike wall-mounted detergent dispensing units, the onboard AXP detergent system takes the guesswork out of correct detergent dispensing. A magnetic control on the AXP detergent cartridge allows for the required dilution ratio to be preset. The correct amount of detergent is then mixed with clean water at the time solution is applied to the floor, allowing for effective and efficient cleaning results.

The AXP system allows for the use of any brand of detergent, including those that are green-certified. Multiple AXP cartridges can be kept on the shelf filled and preset so there are no hassles when switching detergents during cleaning. Imagine the convenience and flexibility to switch detergents within seconds, and without having to clean out the solution tank.

The semi-transparent AXP cartridges are reusable and operator friendly, allowing you to easily spot when refills are needed. The appropriately labeled cartridges are easily transportable to switch detergent types while on the go.

Coverage Rate Low moisture mode – 18,500 ft2 /hour (1,720 m2 ) Restoration mode – 8,000 ft2 /hour (745 m2 ) Slow low moisture/Fast Restoration 10,000 ft2 /hour (930 m2 )
Solution Tank 45 gal (170 L) capacity, Rotationally molded polyethylene with drain hose.
Recovery Bladder 25 gal (95 L) capacity, PVC material, equipped with float ball screen and a 36 in (91 cm), long 1.5 in (3.8 cm) diameter drain hose
Brush Speed 900 rpm
Brush Length 28 in (71 cm)
Brush System 2 motors at 0.75 hp, 560 W each
Solution Pump Low moisture mode – 0.5 gpm (1.9 L/min) at 100 psi Restoration mode – 1.1 gpm (4.1 L/min) at 100 psi
Vacuum Motor 0.80 hp, 600 W motor with gear transmission, band brake and dynamic braking.
Drive System 1.1 hp, 840 W motor with gear transmission, band brake and dynamic braking. Programmable speeds up to 4.5 mph transport, and 3.8 mph scrubbing.
Power Source Six 6 V / 238 Ah (@ 20 hour rate) batteries or Six 6 V / 305 Ah (@ 20 hour rate) batteries
Sound Level 73 dB A @ operator position.
Min. Turn-around Aisle Width 63 in (160 cm) right or left
Dimensions Length – 60 in (152 cm) Width – 31 in (79 cm) Height – 51 in (130 cm)
Weight Net – 625 lb (283 kg) without batteries Net – 1,165 lb (528 kg) with batteries Shipping – 1,433 lb (649 kg) with batteries and charger

Parts

  • Product
  • Qty in Cart
  • Quantity
  • Price
  • Subtotal
  • ships same day
    OEM
    56382693 - Wheel and bearing assembly 172-3283

    Wheel and bearing assembly 172-3283

    $320.69
    Matches:172-3284172-8804272-3547272-85743140333165403826934123174123415631403356316540563165415638269356412317564123415660148260148286745030Commonly purchased together:May fit on these models - select model and diagram to confirmNilfisk-Advance Liberty...
    $320.69
    Qty in Cart: 0
    Price:
    $320.69
    Subtotal:
  • ships same day
    OEM
    56383319 - Drain hose 172-3352

    Drain hose 172-3352

    $38.79
    Specifications:Weight: 1.062 poundsMatches:272-53303144873146215631448756314621563819185638331956601401566014046014016014048.669-966.0866996608803803091009710W74586Commonly purchased together:May fit on these models - select model and diagram to...
    $38.79
    Qty in Cart: 0
    Price:
    $38.79
    Subtotal:
  • ships same day
    OEM
    56115344 - Idler end assembly 172-3373

    Idler end assembly 172-3373

    $56.72
    Matches:115344172-8934172-8961272-21533144453154484074454074694075545611534456314445563154485640744556407469564075548672658091073590Commonly purchased together:May fit on these models - select model and diagram to confirmNilfisk-Advance CONVERTAMATIC...
    $56.72
    Qty in Cart: 0
    Price:
    $56.72
    Subtotal:
  • ships same day
    OEM
    9100000818 - Float cage half (2 required for full float cage) 172-0517

    Float cage half (2 required for full float cage) 172-0517

    $19.25
    This is only half of the float cage, you need 2 to make an entire float cage. Does not include the ball, part number 172-0192.Specifications:Weight: 0.01...
    $19.25
    Qty in Cart: 0
    Price:
    $19.25
    Subtotal:
  • ships same day
    OEM
    314760 - Vacuum duct gasket 272-0430

    Vacuum duct gasket 272-0430

    $14.41
    Matches:172-333631409931476056314099563147608675313086753150Commonly purchased together:Fits on:Nilfisk-Advance AQUACLEAN 18FLXNilfisk-Advance AQUACLEAN XPNilfisk-Advance AQUAPLUSNilfisk-Advance Liberty SC60Nilfisk-Advance AQUACLEAN 16STClarke (Alto)...
    $14.41
    Qty in Cart: 0
    Price:
    $14.41
    Subtotal:
  • ships same day
    OEM
    56314373 - Filter 172-3348

    Filter 172-3348

    $11.35
    Specifications:Length: 6 in Width: 3 in Height: 1 in Color: BlackMaterial: MeshType: StandardMatches:3143735631437386728350Commonly purchased together:Fits on:Nilfisk-Advance Advenger 2810DNilfisk-Advance ADVENGER 3210D-WMNilfisk-Advance ADVENGER...
    $11.35
    Qty in Cart: 0
    Price:
    $11.35
    Subtotal:
  • ships same day
    OEM
    391690 - Float ball 172-0192

    Float ball 172-0192

    $10.52
    Specifications:Weight: 0.012 poundsMatches:08812373170-9085225-0093272-546439169056391690572-34449100000817L08812373Commonly purchased together:May fit on these models - select model and diagram to confirmNilfisk-Advance AQUACLEAN 18FLXClarke (Alto)...
    $10.52
    Qty in Cart: 0
    Price:
    $10.52
    Subtotal:
  • Non-OEM
     - Clear vinyl tubing 9/16 OD x 3/8 ID inch (sold by the inch) 991-1409

    Clear vinyl tubing 9/16 OD x 3/8 ID inch (sold by the inch) 991-1409

    $0.55
    Matches:272-04575664484564484588019130TTS XVJG 9/16" X 3/8" X 100'May fit on these models - select model and diagram to confirmTennant 5680Tennant 5700 SERIESTennant M20Tennant T20Nobles EZ RIDER HPTennant M30Nilfisk-Advance AQUA RIDE SETennant 4300...
    $0.55
    Qty in Cart: 0
    Price:
    $0.55
    Subtotal:
  • OEM
    316105 - Control panel assembly (OBSOLETE) 272-7213

    Control panel assembly (OBSOLETE) 272-7213

    Call for availability
    Matches:31610556316105May fit on these models - select model and diagram to confirmNilfisk-Advance AQUA RIDE SENilfisk-Advance AQUA RIDENilfisk-Advance AQUARIDE AXPNilfisk-Advance AQUA RIDE BRX 700Nilfisk-Advance BRX 700
    $1,490.92
    Qty in Cart: 0
    Price:
    $1,490.92
    Subtotal:
  • OEM
    413846 - Gasket strip 272-6565

    Gasket strip 272-6565

    $12.89
    Matches:172-3339314103413846563141035641384686753120Commonly purchased together:Fits on:Nilfisk-Advance ADVENGER 2810DNilfisk-Advance ADVENGER 3210D-WMNilfisk-Advance ADVENGER 3210DNilfisk-Advance ADGRESSOR 3820DNilfisk-Advance AQUA RIDE...
    $12.89
    Qty in Cart: 0
    Price:
    $12.89
    Subtotal:
  • OEM
    56109539 - Recovery tank lid and gasket 272-5303

    Recovery tank lid and gasket 272-5303

    $37.27
    Specifications:Weight: 0.2 poundsMatches:109539172-3350172-33543144613144915610953956314461563144918675061086783010Commonly purchased together:Fits on:Nilfisk-Advance ADVENGER 2810DNilfisk-Advance ADVENGER 3210D-WMNilfisk-Advance ADVENGER...
    $37.27
    Qty in Cart: 0
    Price:
    $37.27
    Subtotal:
  • OEM
    56315447 - Idler bearing plate 272-2170

    Idler bearing plate 272-2170

    $28.34
    Matches:172-1840172-3374314442315447397448563144425631544756397448May fit on these models - select model and diagram to confirmNilfisk-Advance CONVERTAMATIC 26D-CNilfisk-Advance C-MAX34STNilfisk-Advance SC750Nilfisk-Advance AQUAPLUSNilfisk-Advance...
    $28.34
    Qty in Cart: 0
    Price:
    $28.34
    Subtotal:
  • Total: items /

Adding your products to cart

Can't find what you need? Click here or call 1-800-USA-CLEAN
best live chat